Linear J-S Manual do Utilizador

INSTALLATION AND OWNER’S MANUAL As of date of manufacture, meets all ANSI/UL 325 Safety Requirements for Vehicular door operators J-S & H

4) Depress the limit nut retaining Plate (D) so it disengages from the slots in the limit nuts. Turn the OPEN limit nut (E) on the shaft until it en

RISK OF ENTRAPMENT THAT MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. DISCONNECT POWER TO THE OPENER BEFORE AND DURING INSTALLATION OF AN ACCESSO

9. See Figure 16 for connecting the photoelectric device to the operator. See Page 15 for proper setting of the selector switches. These switches mu

MOTOR CONTROL BOARD Figure 9 OPENTB1STOPCLOSEOPENCOMCLOSESTOPNO REVNC REVPHOTOCOMSINGLEILOCK24 VACCOMSAFE FINISH PHOTOBEAM3-WIRE PHOTOBEAMDoor Edge a

NOTE: It is now necessary to turn on the power in order to change the Operating Mode (if applicable), program any changes desired to the operator’s o

AVOID ELECTROCUTION: DO NOT ROUTE LOW VOLTAGE WIRES IN SAME CONDUIT AS HIGH VOLTAGE WIRES. FOLLOW ALL LOCAL ELECTRICAL CODES OR THE NATIONAL ELECTRI

Changing the Switch Selectable Operation Modes The following modes are selected by setting the on-board dip switches, Figure 14 at right shows where t

Mid-Stop: Activation stops an opening door; momentary contact of open button at mid stop will restart door to full open position; if door is moving op

The solenoid operated brake may require occasional adjustment. Adjustment is necessary if door tends to drift downward after reach

CLUTCH ADJUSTMENT The clutch serves to protect the door, the electric operator and other equipment from undue stress or damage caused by starting forc

READ THESE STATEMENTS CAREFULLY AND FOLLOW THE INSTRUCTIONS CLOSELY. The Warning and Caution boxes throughout this manual are there to protect you

OPERATION & ADJUSTMENT INSTRUCTIONS 20

Following installation, the operator MUST be tested and respond correctly to all controls as specified on the wiring diagram. KEEP personnel and equip

WIRING DIAGRAM/SCHEMATIC - SINGLE PHASE 22 575 VOLTS, 3 PHASESINGLE VOLTAGE MOTORBL/BLKBL/BLKTO REVERSE MOTOR, SWITCH LEADS 1 & 3L14L2YELLOWWHITEB

575 VOLTS, 3 PHASESINGLE VOLTAGE MOTORBL/BLKBL/BLKTO REVERSE MOTOR, SWITCH LEADS 1 & 3L14L2YELLOWWHITEBLACKORANGEBLUEREDWire Nut Connection3BLUE (

24 NOTES

Ref Part# Description Assemblies A 105933 Frame Assembly w/Shafts. J 109318 Frame Assembly w/Shafts, H C 106501 Drive Shaft Assembl

26 SPECIFICATIONSMODEL : J_ _ _ _S HP:_____VOLTS : _____ PHASE : _____* UL AND CANADIAN UL LISTED* HIGH STARTING TORQUE, CONTINUOUS D

The purpose of this booklet is to provide assembly, installation and operation information concerning Model J-S & H-S Commercial Vehicular Garage

Before starting the installation of the operator, the door must be in good working condition and properly counterbalanced. Inspect the door and track

COMPONENT IDENTIFICATION LISTING ITEM PART # DESCRIPTION QTY ITEM PART # DESCRIPTION QTY 1 Per Model Operator Power Head 1 8 009149 Relea

SPRINGS, PULLEYS, CABLES AND MOUNTING HARDWARE USED TO BALANCE YOUR GARAGE DOOR ARE UNDER EXTREME TENSION AT ALL TIMES AND CAN CAUSE SEVERE INJURY O

CHAIN HOIST AND FLOOR DISCONNECT INSTALLATION If the operator is furnished with a chain hoist (Model H-S), pass the hand chain over the chain whe

Figure 6 100719 Right Side Mount Ceiling Mount Left Side Mount Ceiling Mount Center Mount Direct Couple Wall Mount Wall Mount 8 FIGURE 4 - OPERATOR MO

107841 Figure 7 - Dimensions Model H-S Figure 7A - Dimensions Model J-S 108203 9 FIGURE 5 - OPERATOR DIMENSIONS - MODEL J-S & H-S