Linear RE-1 Manual do Utilizador Página 4
- Página / 32
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
2
INSTALLATION INFORMATION
Before beginning installation, please review the entire instructions
and become familiar with the system’s operation, wiring, and
programmable options.
System Location
For pedestrian door or gate installations, mount the Entry System
on a rigid wall near the controlled door. Avoid mounting the unit
in a location where regular mechanical shock will occur due to a
slamming door or spring loaded pedestrian gate.
For vehicular gate installations, mount the Entry System in clear
view of the gate, but far enough from the gate so the user cannot
touch the gate from the keypad.
★ WARNING FOR ALL GATE INSTALLATIONS: TO AVOID
SERIOUS INJURY OR DEATH, MAKE SURE THAT THE
UNIT IS FAR ENOUGH FROM THE GATE SO THAT THE
USER CANNOT TOUCH THE GATE WHILE OPERATING
THE KEYPAD. HOWEVER, FOR SAFETY, THE GATE
MUST BE FULLY VISIBLE FROM THE KEYPAD.
RFI Filter Installation
An in-line ferrite RFI fi lter has been included with this unit to install
during the wiring of the RE-1 Residential Telephone Entry System.
✦ NOTE: To insure FCC Part 15 Class B compliance, the following steps
must be performed at the time the RE-1 is installed.
1. Open the ferrite RFI fi lter case by gently pulling on the side locking
tab and swinging the case open (see Figure 1).
★ CAUTION: The ferrite parts of the RFI fi lter are fragile.
DO NOT DROP THE FILTER ON A HARD SURFACE!
Damage to the fi lter may result.
2. After completing the RE-1 installation, route all wires except the
AC transformer and telephone lines through the grove in the ferrite
core of the RFI fi lter. The fi lter must be installed outside of the RE-1
case. With the wires captured inside, close the ferrite RFI fi lter case
and snap it shut (see Figure 1).
✦ NOTE: Be sure the fi lter is located no further than two inches from the
rear case cover of the RE-1.
Telephone Wires
The quality of the system’s audio communications is related to the
type of telephone wire and its installation. Noise and hum can be
introduced into the telephone wires. Use only high-quality telephone
wire rated for direct underground burial. All telephone wire should
be twisted-pair.
• Minimum size of 24 AWG for up to 800 feet.
• Minimum size of 22 AWG for up to 1600 feet.
• Minimum size of 20 AWG for up to 2200 feet.
• Minimum size of 18 AWG for up to 3600 feet.
DO NOT ROUTE TELEPHONE AND AC WIRING INSIDE THE
SAME CONDUIT. Route all telephone wires inside a dedicated
conduit that is at least six inches away from any AC line wiring.
Power Supply
Use the supplied 16-volt 20-VA transformer to power the RE-1.
DO NOT POWER ANY OTHER EQUIPMENT FROM THE SAME
TRANSFORMER, use a separate power supply. Keep the system
power wires as short as practical to reduce the chance of noise and
hum pickup.
• For low voltage power wire runs up to 100 feet, use 18 AWG, THHN
600-volt insulated wire.
• For low voltage power wire runs up to 200 feet, use 16 AWG, THHN
600-volt insulated wire.
• Use 22 AWG or larger (depending on the load) for all other
connections.
ALWAYS REMOVE POWER PRIOR TO SERVICING
Earth Ground
To avoid damage to the unit from static discharges, connect the
RE-1’s EARTH GROUND and case ground terminals to a good
earth grounding point within 10 feet. The case ground terminal is
the #8 screw located on the backplate above the wire entry hole.
Also, the RE-1’s Telephone Bypass Module must be grounded to
provide surge protection for the telephone line. Suggested wiring
size is 12 AWG for earth ground.
Removable Terminal Strips
For convenience, the RE-1 is provided with removable terminal
strips. It is important that these strips be removed evenly in order to
avoid causing permanent damage to them.
1. Be certain power is off before removing or installing these strips.
2. With a small screwdriver, gently slide the blade between the terminal
strip and protective label.
3. Slightly pry fi rst one end, then the other, and then the middle. Repeat
the process until the terminal strip can be removed straight off the circuit
board by hand. Be very careful to not damage circuit board traces.
4. When re-installing the terminal strips, press down straight and evenly.
Do not remove or install one end fi rst. This will bend pins on the circuit
board, which will damage the terminal strip internally. This damage
is permanent and can not be repaired by simply straightening the
pins on the circuit board.
✦ NOTE: Unscrew the terminal screws several turns before inserting
wires.
PULL ON PLASTIC TAB
TO UNLOCK FILTER CASE
SWING FILTER
CASE OPEN
FERRITE
CORE
RFI FILTER
INSTALLED
WITHIN 2"
OF RE-1 CASE
PHONE AND
TRANSFORMER WIRES
OUTSIDE OF FILTER
NOTE: INSTALLATION OF THE RFI FILTER WILL
INSURE MAXIMUM RADIO RECEPTION RANGE
FOR ACCESS TRANSMITTERS
Figure 1. RFI Filter Installation
- Residential Telephone 1
- Entry System 1
- PRODUCT DESCRIPTION 3
- INSTALLATION INFORMATION 4
- COMPONENT LOCATIONS 5
- WIRING DIAGRAM 6
- ENTRY SYSTEM MOUNTING 7
- TELEPHONE WIRING 7
- TELEPHONE WIRING OPTIONS 8
- MULTIPLE UNIT INSTALLATIONS 9
- CONTROL WIRING 10
- OPTIONAL REMOTE KEYPAD 11
- OPTIONAL KEYSWITCH 12
- OPTIONAL CCTV CAMERA 13
- PROGRAMMING ACCESS 14
- UN-CHECK THESE 15
- THREE BOXES 15
- LOCAL PROGRAMMING ACCESS 20
- REMOTE PROGRAMMING ACCESS 20
- PROGRAMMING REFERENCE 21
- EDOCRETSAMEDOCRETSAM 21
- EDOCRETSAM 21
- BASIC SYSTEM PROGRAMMING 22
- ENTRY CODE PROGRAMMING 22
- TRANSMITTER PROGRAMMING 23
- TELEPHONE PROGRAMMING 23
- ADVANCED SYSTEM PROGRAMMING 24
- SYSTEM ADJUSTMENTS 26
- RE-1 OPERATION 27
- SPECIFICATIONS 29
- DIMENSION DRAWING 29
- TROUBLESHOOTING 29
- PROGRAMMING WORKSHEET 30
- LINEAR LIMITED WARRANTY 32
Samsung SOC-4120AN manuály
Uživatelské manuály a uživatelské příručky pro Bezpečnostní kamery Samsung SOC-4120AN.
Poskytujeme 1 manuály pdf Samsung SOC-4120AN ke stažení zdarma podle typů dokumentů: Specifikace
Samsung SOC-4120AN Specifikace (73 strany)
Značka: Samsung | Kategorie: Security cameras | Velikost: 3.61 MB |
Tabulka s obsahem
Connector
14
Lens Drives:
18
Camera Unit
21
Tamper Alarm
26
Alarm Set-up
26
Test Mode
29
Using RX3
35
Alarms
51
Diagnostics
59
Pattern
59
Overlay
66
Další produkty a příručky pro Bezpečnostní kamery Samsung
| Modely | Typ Dokumentu |
|---|---|
| SID-70 |
Manuál s instrukcemi
Samsung SID-70 Instruction manual,
20 stránky
|
| SNC-C7478 |
Uživatelský manuál
Samsung SNC-C7478 User manual,
72 stránky
|
| Z-300M |
Uživatelská příručka
Samsung Z-300M User guide,
25 stránky
|
| SNP-6200H |
Uživatelský manuál
Телекамеры SNP-6200(H)P - Samsung,
134 stránky
|
| SPD-3300 |
Uživatelský manuál
 
Manuale istruzioniCamera Dome PTZ SPD-3300,
34 stránky
|
| SCC-C6403P |
Manuál s instrukcemi
Samsung SCC-C6403P Instruction manual,
29 stránky
|
| SVR-1630 |
Uživatelský manuál
SAMSUNG Digital CCTV Systems Advanced Digital Security Solutions,
42 stránky
|
| SNO-1080R |
Uživatelský manuál
Samsung SNO-1080R User manual,
88 stránky
|
| SND-3080CF |
Uživatelský manuál
Samsung SND-3080CF User manual,
109 stránky
|
| SCV-3082 |
Uživatelský manuál
Samsung SCV-3082 User manual,
40 stránky
|
| SIR-4160 |
Uživatelská příručka
Samsung SIR-4160 User guide,
19 stránky
|
| SCC-B5344 |
Uživatelský manuál
Descargar - Belltel Limitada,
89 stránky
|
| SDC-313 SERIES |
Manuál s instrukcemi
Samsung SDC-313 SERIES Instruction manual [en] ,
14 stránky
|
| SND-3080P |
Uživatelský manuál
H.264 - Samsung,
4 stránky
|
| SID-46C |
Uživatelský manuál
The Power of Business - G4S SECURE SOLUTIONS,
21 stránky
|
| SNV-5010 |
Uživatelský manuál
Samsung SNV-5010 User manual,
93 stránky
|
| SCC-B5305(G)(P) |
Uživatelský manuál
Y`ello,
17 stránky
|
| SCC-B5331P |
Uživatelský manuál
  
Samsung SCC-B5331P Instrukcja obsługi,
173 stránky
|
| SCD-3083 |
Uživatelský manuál
Samsung SCD-3083 User manual,
38 stránky
|
| SCP-2120 |
Uživatelská příručka
Samsung SCP-2120 User guide,
45 stránky
|
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.027 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais